Myco Wall Bracket Accessory

When fitting a Swivel Bather or bathboard, there has to be sufficient support from the bath to securely fit the product. In some instances, where the bath has been set into the wall, or if the wall has been tiled, the lip on the bath may not be wide enough to provide the required support.

The stainless steel Myco Wall Bracket is designed to support a Swivel Bather when the lip on the wall side of the bath is less than the recommended 1¼ inches (30mm).

When using a Swivel bather it needs at least 1¼ inches (30mm) of each arm of the base unit to rest on the bath sides.

The wall bracket is located so that it rests on the edge of the bath and is secured to the wall using suitable fixings. When fixing the wall bracket to the wall, the same considerations apply as for the fixing of grab rails.

The wall bracket is 560mm long, with an array of screw holes to allow a good fixing to the wall with appropriate fittings (screws & wall plugs not supplied) and the lip is 45mm wide.

The Myco Wall Bracket is constructed from epoxy coated stainless steel. The dimensions are 22″ x 3″ x 1.75″ (560mm x 80mm x 45mm).

Step 1 The Myco Wall Bracket

The Wall Bracket is designed to support a Swivel Bather™ when the lip on the wall side of a bath is too narrow (less than 1¼ inch 30mm). It is suitable for use with all Myco Swivel Bather models.

2. Fitting the wall bracket

The wall Bracket is attached to the wall as shown:

Fixings will depend on the wall constructions. Stainless steel fixings are recommended

Choose either the small or large holes in the bracket and attach the bracket to the wall using 6 fixings
Download Instruction Manual

 

Myco Seat Raiser Accessory

The Myco Seat Raiser increases the seat height to a more comfortable level. It is particularly useful when the Swivel Bather is used on a bath with low sides, or for taller users who find the seat too low.

For users with limited knee or hip mobility a raised seat allows easier transfer of legs over the side of the bath.

Three models are available:
The standard 3″ (75mm) model (MSR) and a 6″ (150mm) model (MSR6) can be fitted to all Swivel Bathers except the Ultra Swivel Bather &  Swivel Shower Chair.
The 4” model can only be fitted to the Ultra Swivel Bather & Ultra Swivel Shower Chair.

These can be attached to any Swivel Bather model. They are constructed using Stainless Steel and a white epoxy coating.

The Seat Raiser bolts onto any Swivel Bather base frame. Screws and self locking nuts are provided. (A pair of spanners is required to tighten the nuts.)

Note: Not suitable for use with other manufacturers products.

Myco Seat Raiser 3″ MSR
Max user Weight 20stone
127kg
Myco Seat Raiser 6″ MSR6
Max user Weight 20stone
127kg

 

 

 

 

 

 

Myco Seat Raiser| Instructions

Step 1

Place the Myco Seat Raiser over the central pin on the base of the Swivel Bather.

Step 2

Ensure that the holes in the base of the seat raiser line up with the holes in the Swivel Bather base.

Step 3

Using the bolts and nuts provided fix the seat raiser to the base. Tighten all four bolts using two spanners. (The bolts are self locking and require more pressure than hand-tightening can provide.)

Step 4

The seat of the Swivel Bather can then be placed over the new raised height pin and will operate in exactly the same way as the Swivel Bather without the device.

Note: This product is only suitable for use with a Myco Swivel Bather®. It is not safe to use with any other rotating bath seats.